
Round Electromagnets
Flat-faced round electromagnets or holding solenoids from 0.50" to 4.0" dia. These APW electromagnets or holding solenoids available with either thru hole mounting or a female tapped mounting threads. Round holding solenoid electromagnets are available in 3 vdc to 230 vac voltages holding 2 to 640 lbs.
-
0.50" Dia. 24V Electromagnet, DC, holding solenoid - 2 lbs.
This industrial electromagnet magnet is equipped with 24 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 24
- Amps: 0.04
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Duty continuous
- Current: DC
- Bolt Desc. or Thread Female 2-56
- Holding Force: 2 pounds
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-24-222
-
0.50" Dia. 3V Electromagnet, DC, holding - 2 lbs.
This industrial electromagnet magnet is equipped with 3 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical Voltage: 3
- Bolt Desc. or Thread Female 6-32
- Amps: 0.33
- Current: DC
- Holding Force: 2 pounds
- Duty continuous
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-3-222-A -
0.50" Dia. 6V Electromagnet, DC, Holding - 3 lbs.
This industrial electromagnet magnet is equipped with 6 volts of direct current with 3 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 6
- Holding Force: 3 pounds
- Amps: 0.28
- Current: DC
- Bolt Desc. or Thread Female 2-56
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Duty Intermittent
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-6H-222
-
0.50" Dia. Electromagnet, 24 VDC, holding solenoid - 2 lbs
This industrial electromagnet magnet is equipped with 24 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 24
- Amps: 0.04
- Bolt Desc. or Thread Female 6-32
- Current: DC
- Holding Force: 2 pounds
- Duty continuous
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-24-222-A
-
0.50" Dia. Electromagnet, 28 VDC, holding solenoid - 2 lbs.
This industrial electromagnet magnet is equipped with 28 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 28
- Amps: 0.037
- Bolt Desc. or Thread Female 6-32
- Current: DC
- Holding Force: 2 pounds
- Duty continuous
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-28-222-A
-
0.50" Dia. Electromagnet, 3 VDC, small holding solenoid - 2 lbs.
This industrial electromagnet magnet is equipped with 3 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical Voltage: 3
- Amps: 0.33
- Current: DC
- Bolt Desc. or Thread Female 2-56
- Holding Force: 2 pounds
- Duty continuous
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-3-222
-
0.50" Dia. Electromagnet, 9 VDC, holding - 2 lbs.
This industrial electromagnet magnet is equipped with 9 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 9
- Amps: 0.11
- Current: DC
- Bolt Desc. or Thread Female 2-56
- Holding Force: 2 pounds
- Duty continuous
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-9-222
-
0.50" Dia. Electromagnet, 9 VDC, holding - 2 lbs.
This industrial electromagnet magnet is equipped with 9 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 9
- Amps: 0.11
- Bolt Desc. or Thread Female 6-32
- Current: DC
- Holding Force: 2 pounds
- Duty continuous
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-9-222-A
-
0.50" Dia. Mini Electromagnet, 6 VDC, holding - 3 lbs.
This industrial electromagnet magnet is equipped with 6 volts of direct current with 3 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 6
- Holding Force: 3 pounds
- Bolt Desc. or Thread Female 6-32
- Amps: 0.28
- Duty intermittent
- Current: DC
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-6H-222-A