Sale
Sort by:
Recommended
-
-
-32%
Round Electromagnet, 0.50" Dia With 12 VDC
This industrial electromagnet magnet is equipped with 12 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 12, Current: DC
- Bolt Desc. or Thread Female 2-56
- Holding Force: 2 pounds
- Duty continuous
- Amps: 0.08
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-12-222
-
-
-
-32%
0.50" Dia. 24V Electromagnet, DC, holding solenoid - 2 lbs.
This industrial electromagnet magnet is equipped with 24 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 24
- Amps: 0.04
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Duty continuous
- Current: DC
- Bolt Desc. or Thread Female 2-56
- Holding Force: 2 pounds
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-24-222
-
-
-
-32%
0.50" Dia. Miniature Electromagnet, 6 VDC, holding solenoid - 2 lbs.
This industrial electromagnet magnet is equipped with 6 volts of direct current with 2 pounds of magnetic suck. It is not a quick release and does not offer encapsulation or include an anti-rotation pin.
Features:
- Electrical- Voltage: 6
- Amps: 0.16
- Current: DC
- Lead Wire Ga: 28
- Lead Wire Length: 11 inches
- Bolt Desc. or Thread Female 2-56
- Duty continuous
- Holding Force: 2 pounds
- Outer Diameter: .5 Inches
- Height: .5 inches
The included tapped rear-threaded mounted option offers superior versatility. The mounting screw is not provided and the lead wire type is a TFE. This magnet cannot handle high temperatures (i.e. above 500 degrees fahrenheit) nor is it magnetic stainless (430 FR).\
*The holding force for this round electromagnet is tested on a load cell under a standardized test method. Our standardized test includes direct contact with a bare 1215 CRS ground strike plates. The plates are .240” thick and are either greater than or equal to the diameter of the electromagnets.
EM050-6-222
-
-
-
-21%
EMD-FOFO-v1_3
Electromagnet Driver Circuit - Fast on Fast off Ver. 1_3 Driver allows for rapid on time and instant release of work hold material using a reverse current spike.
-
-
-
-10%
EM400-24-212
4.0" Dia. 24-volt DC Electromagnet, holding - 640 lbs. Accommodate a lighter load with this strong 24-volt electromagnet of the same size.
-
